0
Add your answer:
Earn +20 pts
How do you set ignition timing on a 1989 ford probe?
where are timing marks on 89 ford probe 4 cylinder I have the bottom not the top
97 ford probe gt 2.5 ticking rattling noise coming from the timing belt?
more than likely the tensioner
Is 1996 4 cylinder Ford Probe SE an interference engine?
Yes, the 2.0 liter 4 cylinder engine in a 1996 Ford Probe is an interference engine ( according to the Gates website , they make timing belts etc. )
What can be done about a ticking or rattling noise coming from either the timing belt or the rear camshaft on a 95 Probe 2.5 GT?
It sounds like your timing belt hydraulic tensioner arm is bad, they are very expensive.
Is the 4 cylinder engine in a 1996 Ford Probe SE an interference engine?
Yes , according to the Gates website the 2.0 liter 4 cylinder in a 1996 Ford Probe IS an interference engine
Timing Ford Probe?
{| ! valign="bottom" | Item ! valign="bottom" | Part Number ! valign="bottom" | Description | 1 6M250 Timing Chain/Belt Idler, Upper 2 6256 Camshaft Sprocket, Front 3 6M250 Timing Chain/Belt Idler, Lower 4 6306 Crankshaft Sprocket 5 6K254 Timing Chain/Belt Tensioner 6 6256 Camshaft Sprocket, Rear Removal # Remove the Engine Front Covers (6019). Refer to the procedure in this section. # Remove the three nuts and the engine support insulator through bolt from the engine support insulator. Remove the front engine support bracket (6028). # Raise and support the vehicle. # Align the crankshaft sprocket (6306) to TDC by turning the crankshaft (6303) in the direction of normal engine (6007) rotation. # NOTE: Remove the lower timing chain tensioner arm bolt before the upper timing chain tensioner arm bolt. Remove two bolts from the timing chain tensioner arm (6285) in the order shown. Remove the timing chain tensioner arm. # Mark the direction of rotation on the timing chain/belt (6268) to be sure of proper installation. # Loosen the timing chain/belt tensioner bolt. # Remove the timing chain/belt. Installation # Compress the timing chain tensioner arm until the hole in the piston is aligned with the second hole in the case. Insert a 1.6mm (0.06 inch) diameter wire or pin through the second hole to keep the piston compressed. # Align the camshafts (6250) to top dead center (TDC). # Turn the crankshaft clockwise until the crankshaft sprocket is offset from TDC by one tooth. # Install the timing chain/belt.Turn the crankshaft in the direction of normal engine rotation without moving the camshafts, until the crankshaft timing mark is again at TDC. This will place all of the belt slack in the timing chain tensioner arm portion of the timing chain/belt. # Install the timing chain tensioner arm and both bolts. Tighten the timing chain tensioner arm bolts to 19-25 Nm (14-18 lb-ft). # Remove the pin from the timing chain tensioner arm. # NOTE: When correctly timed, the crankshaft timing mark will line up and will NOT be one tooth off. Turn the crankshaft two complete revolutions, in the direction of normal engine rotation, to make sure that the timing is still correct. # Tighten the timing chain/belt tensioner bolt to 35-51 Nm (26-37 lb-ft). # Install the RH engine support insulator. Tighten the three nuts to 74-103 Nm (54-76 lb-ft) and the RH engine support insulator through bolt to 67-93 Nm (50-68 lb-ft). # Install the Engine Front Covers . |}
How much would it cost to install a water pump in a 1995 Ford Probe 4 cylinder?
a 4 cylinder probe im not sure but i got the gt model and they want 600-800 from places i checked at so probably around 300-400 for yours
1994 probe GT 2.5 v6 5speed - Will the timing belt tensioner cause a little ticking noise and if so is it hard to install one or costly to replace the belt?
Failing bearings and spring loadings of the tensioner assembly can cause noise and belt tracking. However, timing and other mechanical issues can also cause ticking and clicking noises. The tensioner and idler pullies in addition to the belts are not considered a costly repair for this application. It is advisable to have the condition verified by a professional before replacing perfectly functional parts. However, belts are routing wear items and should be replaced at appropriate intervals.
What is Ignition timing 1990 Ford Probe 2.2?
motorcraft.com shows for the 1990 Ford Probe 2.2 L ( 133 cubic inch ) 4 cylinder : ignition timing : 6 degrees BTDC , and --------------------------------------------------------------------------------------------------------- 9 degrees BTDC - manual transmission - with turbo - with self test connector grounded
Is the 1997 ford probe 2.0l doh cam a non-interferance engine?
No , according to the Gates website ( they make timing belts etcetera ) the 2.0 liter four cylinder engine in a 1997 Ford Probe ( IS AN INTERFERENCE ENGINE )
How do you put a 93 Ford Probe back in time?
Number 1 cylinder at top dead centre on compression take off distributor cap make sure that roater is on number one cylinder if it dont fire up turn roater 180 degrees. 93 ford probe does not have timing marks
How do you install a supercharger on a Ford probe?
Can a supercharger work on a 97 ford probe
