0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What year did production start for the WB Statesman?
The WB Statesman is a long wheel-base luxury sedan produced by General Motors - Holden WB. It was first introduced into the market in 1980. There were two different models, the de Ville and the Carpice.
Where is the fuel pump assembly on a 2000 olds intrigue located?
In the gas tank. Book procedure for replacing: Remove the negative battery cable. Relieve the fuel system fuel pressure. Remove the rear compartment trim panel - Rear in Body Rear End. Remove the nuts retaining the fuel sender access panel. Remove the fuel sender access panel. Disconnect the fuel sender electrical connectors. Clean the fuel pipes and the fuel sender assembly to prevent fuel contamination during the removal. Disconnect the quick-connect fittings at the fuel sender assembly. Remove fuel sender snap ring retaining the fuel sender. Remove the modular fuel sender assembly. Clean and inspect the O-ring sealing surfaces of the fuel sender assembly . Important Always replace the fuel sender O-rings when reinstalling the fuel sender assembly. The modular fuel sender assembly will spring-up when the snap ring is removed. When removing the modular fuel sender assembly from the fuel tank, the reservoir bucket on the fuel sender assembly is full of fuel. The modular fuel sender assembly must be tipped slightly during removal in order to avoid damage to the float. Place any remaining fuel into an approved container once the modular fuel sender assembly is removed from the fuel tank. Always maintain cleanliness when servicing the fuel system components. Care should be taken not to fold over or twist the fuel pump strainer when installing the fuel sender assembly, as this will restrict fuel flow. Also, ensure that the fuel pump strainer does not block full travel of float arm. Ensure that the snap ring retaining the fuel sender assembly is fully seated within the tab slots on the fuel tank. Position the new fuel sender assembly O-ring on the fuel tank. Install the fuel sender assembly into the fuel tank. The Fuel Sender Assembly is spring loaded, it will be necessary to hold the sender in place. Install the snap ring retaining the fuel sender assembly . Connect the fuel sender assembly electrical connectors. Install the quick-connect fittings at the fuel sender assembly. Connect the negative battery cable. Perform the following procedure to check for fuel leaks: Turn the ignition switch to the ON position for 2 seconds. Turn the ignition switch to the OFF for 10 seconds. Turn the ignition switch to the ON position again. Visually inspect the fuel system for fuel leaks. Install the fuel sender access panel. Good Luck!
How do you change the fuel filter on a 2005 chevy silverado?
The fuel filter is located in the fuel sender assembly, inside the fuel tank. Vehicles with dual tanks, have no fuel filter in the rear tank fuel sender assembly.
Where is the fuel sender located on vauxhall corsa?
hi mate the fuel sender on the corsa should be in the fuel tank as on the majority of cars cheers telboy.
How do you replace the fuel sender on a 1991 buick lesabre?
fuel gauge sender and pump are in the gas tank (which must be removed).
Where is fuel gauge sender on 96 Subaru?
Inside the fuel tank.....
Where is the fuel pump on 1991 Thunderbird?
the fuel pump is located on the fuel sender inside the fuel tank
Where is the fuel pump on 1996 BMW 323i?
Under the back seat there are two access panels to the tank. The fuel pump/sender unit is under the O/S panel and the other sender unit is under the N/S. You can tell the difference as the fuel pump and sender combined unit will have two electrical connectors. The solitary sender only has one and a fuel return pipe i think.
Where is the fuel filter location on a 2004 Pontiac Vibe?
== == The Pontiac Vibe Fuel filter is located on top of the gas tank. you can access it by going thru the cargo floor hatch under the spare tire. The access to the fuel filter in the fuel tank is by removing the bottom of the rear seat. It is not something that needs to be routinely replaced
Why does your 1999 f250diesel fuel gauge stay on full?
The most likely reason is the sender wire (that runs from the sender unit in the fuel tank) is earthing some where along its route.
How do you replace the fuel pump on a 1994 Chevy Suburban V8?
You have to drop the fuel tank, which is quite a project, and then 'unscrew' the fuel sender unit. The sender is held in place by a lock-ring that must be gently hammered loose in a counter-clockwise direction. You can then pull the fuel sender unit out of the tank and replace the fuel pump. The difficult part of this whole process is dropping the fuel tank. Search for "drop suburban fuel tank" for instructions on how to do that.
How do you remove a Holden 1971 HQ fuel sender?
Well, removing a Holden 1971 HQ fuel sender is like painting a happy little tree. First, gently disconnect the fuel lines and electrical connections. Then, carefully unscrew the sender unit from the tank, making sure to support it as you lower it out. And remember, there are no mistakes, just happy little accidents in the world of car maintenance.
