answersLogoWhite

0


Best Answer

The generator circuit breaker or gcb is a circuit breaker which is connected with the generator . Whenever there is a fault in the generator the circuit breaker trips and disconnects the generator from operation thus it helps the place from a serious accident etc..

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is a generator breaker?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Natural Sciences

What size breaker is needed to connect 5500 watt gas powered generator?

A 5500 watt gas powered generator typically requires a 30 amp breaker for a 240 volt connection. It is recommended to consult the manufacturer's specifications to ensure the correct breaker size for your specific generator model.


How do you know if a generator has blown it's breaker?

It won't supply any power.


What size wire and breaker do you need to run a 9000max watt generator?

To determine the wire size and breaker needed for a 9000 max watt generator, you would first need to calculate the running wattage of the generator, as this is the value used for sizing the wire and breaker. Once you have the running wattage, you can then refer to the National Electrical Code (NEC) for guidance on the appropriate wire size and breaker size based on the circuit's length and the type of insulation on the wire. It is recommended to consult with a qualified electrician to ensure the installation meets safety and code requirements.


If all the breakers in your house added up to 765 amps how big of a generator would you need to buy?

To determine the size of the generator needed, you need to consider the total connected load you want to power during an outage, not just the sum of the breakers. It's recommended to work with an electrician to properly calculate the load and size the generator accordingly to ensure it can handle your power needs.


What direction must the synchroscope be travelling when the breaker is closed?

The synchroscope must be moving clockwise to indicate that the generator frequency is slightly higher than the system frequency. This ensures that when the breaker is closed, the two frequencies will synchronize properly.

Related questions

What size breaker can you use on a 7500watt generator?

Depends on the wire size you are using. If the generator breaker is a 30 amp then install a 30 amp breaker.


Can a generator be motored simply by closing generator breaker to energized bus?

No.


What is 52g?

Generator Breaker Status


How is a Load applied to a ac generator?

The load conductor is connected to the load side of the generator breaker. Once the generator is up to speed the load breaker is closed and the voltage is then applied to the load.


What is 52G protection?

Generator Breaker Status


What size breaker is needed to connect 5500 watt gas powered generator?

A 5500 watt gas powered generator typically requires a 30 amp breaker for a 240 volt connection. It is recommended to consult the manufacturer's specifications to ensure the correct breaker size for your specific generator model.


What actions to be taken should a main generator circuit breaker stay connected?

I don't understand the question. <<>> If your generator's main breaker does not trip when an overload occurs on the generator's output the breaker's trip setting needs to be looked at. Usually the molded case breaker's face cover can be removed. This will allow you access to the trip settings. Set the overloads to the maximum generator's output. The short circuit setting should be set at 250% of the maximum generator output. If these parameters can not be met on the existing breaker there might be a chance that the breaker has been changed out at some point in time and the wrong breaker was installed at that time. This scenario happens quite frequently on remote operations where the service has to be maintained and the site doesn't have a second back up generator. The site supervisor usually says "just make it work".


How do you know if a generator has blown it's breaker?

It won't supply any power.


Is both circuit breaker and circuit gear have same functions?

circuit breaker is break the electrical circuit .circuit gear is generator analyzer


What size wire and breaker do you need to run a 9000max watt generator?

To determine the wire size and breaker needed for a 9000 max watt generator, you would first need to calculate the running wattage of the generator, as this is the value used for sizing the wire and breaker. Once you have the running wattage, you can then refer to the National Electrical Code (NEC) for guidance on the appropriate wire size and breaker size based on the circuit's length and the type of insulation on the wire. It is recommended to consult with a qualified electrician to ensure the installation meets safety and code requirements.


How do you flash the field of a generator?

start generator, plug in variable speed drill, set drill to forward, squeeze trigger, quickly spin drill in reverse by hand. be sure generator main breaker is on.


Would a 15 kva 380 volt generator be big enough to run a house with a 60 amp breaker 380 volts?

A 15 KVA - Generator operating at 380 Volts can cater to only 22.79 Amps. It cannot cater to a 60 Amps breaker