0
2. Hold trip meter button (the left button)
3. Ignition key to position 1. The display will show: "test 1"
4. Keep holding the trip meter button until the the display shows: "reset inspection" or "reset oilservice"
5. Release the button
6. Press and release the trip meter buton once. The Display will show the square clock symbol and the month the fluid change is due on
7. Press and hold the trip meter button until the display is showing a flashing "reset". Then release the button. "reset" will keep flashing.
8. Press and release the trip meter button once. The display will show the square clock symbol and the month for the next fluid change
9. Press and hold the trip meter until "End" is displayed
10. Let go of the button and turn ignition key to 0 (off)
Instrutions Courtesy of GoingNuts of e46fanatics.com
What else can I help you with?
How do you reset the low brake fluid warning light in a Chevrolet Impala?
Add brake fluid
How do you reset the brake light on a 2003 clk320?
To reset the brake light on a 2003 CLK320, first, ensure that the brake fluid level is adequate and check for any issues with the brake system. If the fluid is fine, turn the ignition to the "ON" position without starting the engine. Then, press the brake pedal several times, which may help reset the brake light. If the light persists, it might indicate a more serious issue that requires a diagnostic check.
How do you reset brake light on 1991 Mercury Capri after changing front brake pads?
To reset the brake light on a 1991 Mercury Capri after changing the front brake pads, first ensure that the brake fluid level is correct, as low fluid can trigger the light. If the fluid is fine, check the brake light switch, usually located near the brake pedal, to ensure it’s functioning properly. You may also need to disconnect the car battery for a few minutes to reset the dashboard warning light. If the light persists, consult the owner's manual for specific troubleshooting steps.
How do you reset brake fluid light on a 2007 BMW 530xi?
To reset the brake fluid light on a 2007 BMW 530xi, start by turning on the ignition without starting the engine. Use the trip reset button on the instrument cluster to navigate to the brake fluid warning message. Press and hold the trip reset button until the light resets, which typically takes a few seconds. Once the light goes off, turn off the ignition, and then restart the vehicle to ensure the reset was successful.
How do you reset brake warning light?
The light should not have to be reset. The most common problem is low brake fluid, caused by a leak in the system. If the fluid is low fill the reservoir to make the light go out then check the wheel cylinders, as they are the most common leaking points.
How do you reset the brake light on a 1990 Chevrolet pickup?
If you are talking about the red light on the dash then you don't "Reset" it you need to have the brake's serviced or fill-up the fluid in the reservoir. I light is designed to come on if the fluid is low.I also advise you get it serviced if the fluid has not been changed in the last 24 months.Hope This Helps
How do you reset brake fluid light BMW 2007 525i?
You will need a compatible BMW scan tool to reset this service light from the I drive system.
How do you reset the brake warning light on Porsche 928?
To reset the brake warning light on a Porsche 928, first check and ensure that the brake fluid level is adequate and that the brake system is functioning properly. If the fluid level is correct and there are no issues, turn the ignition to the "on" position without starting the engine. Then, press the brake pedal several times; this should reset the warning light. If the light remains on, it may indicate a deeper issue that requires professional diagnosis.
How do you reset brake light on 645Ci?
To reset the brake light on a BMW 645Ci, first, turn the ignition to the "On" position without starting the engine. Press the accelerator pedal three times in quick succession, then turn the ignition off. Start the car again, and the brake light should be reset. If the light remains on, check the brake fluid level and the brake light bulbs for any issues.
How do you reset brake light on dash for a 1994 Cadillac?
To reset the brake light on the dashboard of a 1994 Cadillac, first check the brake fluid level and ensure it's within the proper range. If the fluid level is low, refill it and see if the light turns off. If the light remains on, try disconnecting the battery for a few minutes to reset the system. If the issue persists, it may indicate a problem with the brake system that needs further inspection.
How do you reset ABS light on a Nissan Pathfiner 2000 model?
Add brake oil
How do you reset the Brake Lamp Light on a Acura?
To reset the Brake Lamp Light on an Acura, first ensure that the brake fluid level is adequate and that there are no issues with the brake system. Turn the ignition to the "ON" position without starting the engine. Then, press the gas pedal three times within five seconds. This should reset the Brake Lamp Light; if it remains on, check for any underlying issues with the brake system.
