answersLogoWhite

0


Best Answer

Yes, but you need a power source, for the shunt trip coil voltage, in the circuit.

User Avatar

Wiki User

15y ago
This answer is:
User Avatar
More answers
User Avatar

AnswerBot

5mo ago

No, a shunt trip breaker requires a separate power source to trip the breaker remotely. It cannot be activated by a dry set of contacts alone.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Does a shunt trip breaker work from a dry set of contacts?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Natural Sciences

Can a circuit breaker be tripped by using 20 amp sockets instead of 15 amp sockets?

A circuit breaker protects the wires that the devices are connected to. If the devices that are connected to the circuit are 20 amps the wire size should be #12 wire fed from a 20 amp breaker. This breaker should not trip unless the circuit is overloaded or a fault occurs on the circuit. If the devices that are connected to the circuit are15 amps the wire size should be #14 wire fed from a15 amp breaker. This breaker should not trip unless the circuit is overloaded or a fault occurs on the circuit. Putting 20 amp sockets on this 15 amp circuit will work but the circuit is limited to the amount of load that can be plugged in. You will not get the full capacity of the 20 socket because the breaker will trip at 15 amps.


Why does the breaker continue to trip until hot wire is disconnected?

The breaker is likely tripping due to an overload or short circuit on the circuit that the hot wire is connected to. Disconnecting the hot wire stops the flow of electricity and eliminates the source of the overload, allowing the breaker to reset. It is important to investigate and address the underlying cause of the overload to prevent future tripping.


Can circuit breakers help to prevent building fires?

Breakers limit the current on the conductor to a safe level, too many appliances plugged in. You trip a breaker, hopefully you then transfer load to another circuit. Breakers use two different methods to accomplish this, one uses a bimetallic strip and the current passes directly through, too high a current causes the strip to deflect. It acts on a mechanism much like the sear in a guns trigger, the deflection pulls the trigger causing a spring to open the contacts and turn off the circuit. Another type is thermal magnetic, current passing through the breaker causes a magnetic field to act on a coil tripping the breaker. When breakers are wired and work properly they prevent fires!Bending metal opens a switch


How does a trip switch work?

A trip switch, also known as a circuit breaker, works by detecting an overload or short circuit in an electrical circuit and automatically interrupting the flow of electricity to prevent damage or fire. When the circuit breaker detects an abnormality, it quickly switches off to cut off power and protect the circuit from further damage. Resetting the trip switch restores power once the issue is resolved.


How does a GTE Sylvania GFCI circuit breaker 1 pole 15 a work?

A GFCI breaker monitors the imbalance of current between the ungrounded (hot) and grounded (neutral) conductor of a given circuit. With the exception of small amounts of leak-age, the current returning to the power supply in a typical 2-wire circuit will be equal to the current leaving the power supply. If the difference between the current leaving and returning through the current transformer of the GFCI exceeds 5 mA (61 mA), the solid-state circuitry opens the switching contacts and de-energizes the circuit. Touch the neutral or hot and you change this current which will trip the breaker.

Related questions

How does a shunt trip relay work?

A shunt capacitor creates a low resistance path in a circuit so that electricity can pass around to another point. Shunt capacitors create shorts when they receive abnormally high amounts of voltage to correct series circuits.


Will a 4500 watt element work at all or just trip a 20amp breaker?

A 4500 watt element can work on a 20 amp breaker, but it may occasionally trip if the total load on the circuit exceeds 20 amps. It is recommended to use a 4500 watt element with a 25 amp breaker to ensure consistent performance.


Did my dryer trip the breaker or vice versa when I turned the breaker back on but now the dryer won't work?

The dryer tripped the breaker. Have it repaired. Don't try to use it again. You could cause a fire.


Can to travel in a plane if you have a ventricular shunt?

Yes you can travel in an airplane with a vp shunt. I recently flew from Michigan to Oregon and I have a vp shunt which was placed 6 years ago. One bit of advice though, a sinus decongestent seemed to help with the pressure on the return trip. On the first flight I got a very strong headache, which I believe was caused by the cabin (plane) pressure, so on the return trip I took an Advil Cold and Sinus med. This must work because I had no pressure or pain.


Can you fly if you have a shunt?

i heard u can fly on short journeys Yes, you can fly if you have a shunt, however the affects, as far as the pressurized cabin goes will depend on the type of shunt you have. I have a VP shunt in my head and have no trouble flying and I fly often, as I work for an airline.


Can a 230 v window air conditioner work efficiently using a 220 v plug?

No, it will draw more power then the outlet provides and trip the circuit breaker.


Can a circuit breaker be tripped by using 20 amp sockets instead of 15 amp sockets?

A circuit breaker protects the wires that the devices are connected to. If the devices that are connected to the circuit are 20 amps the wire size should be #12 wire fed from a 20 amp breaker. This breaker should not trip unless the circuit is overloaded or a fault occurs on the circuit. If the devices that are connected to the circuit are15 amps the wire size should be #14 wire fed from a15 amp breaker. This breaker should not trip unless the circuit is overloaded or a fault occurs on the circuit. Putting 20 amp sockets on this 15 amp circuit will work but the circuit is limited to the amount of load that can be plugged in. You will not get the full capacity of the 20 socket because the breaker will trip at 15 amps.


What actions to be taken should a main generator circuit breaker stay connected?

I don't understand the question. <<>> If your generator's main breaker does not trip when an overload occurs on the generator's output the breaker's trip setting needs to be looked at. Usually the molded case breaker's face cover can be removed. This will allow you access to the trip settings. Set the overloads to the maximum generator's output. The short circuit setting should be set at 250% of the maximum generator output. If these parameters can not be met on the existing breaker there might be a chance that the breaker has been changed out at some point in time and the wrong breaker was installed at that time. This scenario happens quite frequently on remote operations where the service has to be maintained and the site doesn't have a second back up generator. The site supervisor usually says "just make it work".


Why does the breaker continue to trip until hot wire is disconnected?

The breaker is likely tripping due to an overload or short circuit on the circuit that the hot wire is connected to. Disconnecting the hot wire stops the flow of electricity and eliminates the source of the overload, allowing the breaker to reset. It is important to investigate and address the underlying cause of the overload to prevent future tripping.


What will happen if you will give ac supply to dc shunt motor?

it will not work.


Can a small mini-fridge be plugged into the same circuit as the washer machine?

Not a good idea in general. There is a large chance that you will trip what I expect is a 20 A breaker controlling the circuit. It may seem to work under some circumstances, but if the refrigerator compressor kicks in while the washer motor is demanding a surge current on motor start-up the breaker will likely trip.


Can circuit breakers help to prevent building fires?

Breakers limit the current on the conductor to a safe level, too many appliances plugged in. You trip a breaker, hopefully you then transfer load to another circuit. Breakers use two different methods to accomplish this, one uses a bimetallic strip and the current passes directly through, too high a current causes the strip to deflect. It acts on a mechanism much like the sear in a guns trigger, the deflection pulls the trigger causing a spring to open the contacts and turn off the circuit. Another type is thermal magnetic, current passing through the breaker causes a magnetic field to act on a coil tripping the breaker. When breakers are wired and work properly they prevent fires!Bending metal opens a switch